IMC Networks IE-MiniFiberLinX-II w/ TELCO Power Manuál s instrukcemi

IE-MiniFiberLinX-II (Non-Telco, Telco and Telco/Last Gasp) Operation Manual Above illustrations are representative; some minor differences may be

7 FiberAlert FiberAlert minimizes the problems associated with the loss of one strand of fiber. Normally when a single strand of fiber is lost, the t

8 Loopback Testing The IE-MiniFiberLinX-II includes Loopback testing functionality. During loopback testing, management traffic entering the uplink

9 The IE-MiniFiberLinX-II is strictly a CPE device; configuration on a Host would require an iMcV-FiberLinX-II; select No Learning on OPTICS and DATA

10 Software Configuration The following table presents port options configurable from iView² or from a serial/Telnet session. Refer to the iView² sec

11 Main Configuration Screen Press Enter, at the prompt, to display the main configuration screen. The following displays are available: Saved Values

12 Command List I = Enter New Saved Parameter Values P = Change Password T = New Trap Destination K = Remove ALL Trap Destinations C = New Communi

13 Removing Trap Destinations To remove all trap destinations, press K. Press Y to continue to confirm or N to abort and then, press Enter. To selec

14 Rebooting the Unit To reboot the IE-MiniFiberLinX-II, type reboot. Enabling/Disabling DHCP To toggle DHCP on the IE-MiniFiberLinX-II between enabl

15 config Allows VLAN and transparency mode configurations. accounts Allows the addition of new users. sysdescr Allows the editing of sysName, sysDesc

16 Viewing Port RMON Statistics To view port RMON (Remote MONitoring) statistics on the IE-MiniFiberLinX-II, enter rmstats. This will display RMON

ii FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A computing device, pursu

17 Version Entering version will display the version of the firmware operating the IE-MiniFiberLinX-II. NOTE In the examples shown, ports are referred

18 NOTE Selective Advertising must be used when connecting to a device that Auto Negotiates and a specific speed and duplex mode is desired. Advertis

19 How to configure the IE-MiniFiberLinX-II for management on the copper port 1. Configure the device to be set in the default mode. If unsure of th

20 Press Enter for device configuration mode. Press the Space Bar once for access to additional commands.

21 Type config then press Enter to set the operation mode. Press Enter for other options.

22 Press 2 to change to Default Plus Mode, then press Enter. Press Y to allow TX management, and then press Enter. Press S to save the configurat

23 Mode Two - Transparency with Untagged Management This mode is designed to pass all tagged and extra-tagged customer traffic unchanged and must be

24 Mode Four - Transparency with Extra Tagging (or Q-in-Q) This mode is designed to either pass all customer traffic with the defined extra tag (Q-i

25 Mode Five - VLAN Filter This mode is designed to only pass traffic with any of the 32 tags that have been identified in the user-defined table. No

26 System Description Sysdescr offers the options of assigning a system name, System Contact System Location, Unit Description and individual Port nam

iii Table of Contents FCC Radio Frequency Interference Statement ...ii Warranty...

27 802.1p Base Pri Set the level of 802.1p base priority (3 or 4). The IE-MiniFiberLinX-II has two outgoing queues; one for high priority traffic and

28 also be performed using Telnet. Multiple accounts can be assigned with individual names and passwords. Each account can be assigned one of the fo

29 The left side of the iView² screen will display the IMC Networks products on the network. Click the connection for the IE-MiniFiberLinX-II to open

30 The Configuration/Remote Screen Depending on whether the IE-MiniFiberLinX-II is being set up as a standalone or in a Host/Remote connection, the Co

31 type through iConfig or TFTP into the unit’s Large File Area. After the transfer is complete, the unit copies the configuration to flash and reboo

32 The user is prompted for a filename: The user is prompted to enter any notes to the header of the saved file for future reference when uploadi

33 Uploading a Saved Configuration File through iConfig From the Administration Tab in iConfig click the Upload Configuration button: The user wi

34 Uploading a Saved Configuration File through TFTP From the commands list in the CLI (Serial or Telnet) run the download command by typing in down

35 The user will be prompted to continue that retrieval process by pressing the ENTER key or cancel by typing “Q”. After the transfer process is com

36 Product Applications The IE-MiniFiberLinX-II comes with a variety of features for different network environments. When used with different types o

1 About the IE-MiniFiberLinX-II Non-Telco, Telco and with Telco/Last Gasp The IE-MiniFiberLinX-II is an optical demarcation network interface device (

37 Modes of Operation The following are application examples of Operation Modes for the IE-MiniFiberLinX-II. There are six modes of operation that ca

38 Mode Three - Transparency with Tagged Management This mode will pass all tagged and untagged customer traffic. Management traffic must be tagged. I

39 Mode Five - VLAN Filter This mode is designed to only pass traffic with any of the 32 tags that have been identified in the user-defined table. No

40 Troubleshooting If a fiber connection cannot be established, perform the following to make sure that the fiber transceivers on the IE-MiniFiberLinX

41 IE-MiniFiberLinX-II Modes of Operations For enlarged version go to IMC Networks website: http://www.imcnetworks.com/Products/12_IE-MiniFiberL

42 The Agent Info Screen Information about the SNMP Agent software managing the IE-MiniFiberLinX-II is contained on this screen. Specifications Input

43 Fiber Optic Cleaning Guidelines Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, whi

44 Safety Certifications UL/CUL: Listed to Safety of Information Technology Equipment, including Electrical Business Equipment. CE: The produc

19772 Pauling • Foothill Ranch, CA 92610-2611 USA TEL: (949) 465-3000 • FAX: (949) 465-3020 www.imcnetworks.com © 2011 IMC Networks. All rig

2 Management The IE-MiniFiberLinX-II is capable of accepting IP-based management traffic from its Data and/or Fiber ports. Management can be configu

3 Installation To install the IE-MiniFiberLinX-II into a network environment, connect the proper twisted-pair and fiber cables. In a standalone confi

4 LED Operation The IE-MiniFiberLinX-II features two diagnostic LEDs: FX LNK/ACT This LED is on when a FX Link exists and blinks when data passes thr

5 CAUTION: This equipment is designed to permit the connection of the grounded conductor of the DC supply circuit to the grounding conductor at the e

6 The IE-MiniFiberLinX-II ships from the factory with Auto Negotiation enabled on the twisted pair port. In this mode, the port automatically negotia