IMC Networks Giga-AccessEtherLinX-II Manuál s instrukcemi

Giga-AccessEtherLinX-II Operation Manual The above illustration is representative; some minor differences may be present in actual product

7 NOTE Reboot after making any modifications to the Saved Values or the changes will not take effect. To reboot, type Reboot at the prompt on the mai

8 default public string. To create a new community string, go to the main configuration screen and press C. Enter the name of the new community (up

9 E Ending a Session Be sure to press E before disconnecting the cable in order to stop the continuous stream of data to the console port. Space Bar

10 cleandb Reboots the Giga-AccessEtherLinX-II with a clean database. This removes all of the information in the database with an option to change th

11 *A reboot may be required for some configuration changes to take effect. Downloading Files Firmware and configuration files for the Giga-AccessEthe

12 connection between ports includes management. Management can be assigned a VLAN. Mode 5 Only accepts untagged traffic at the Downlink Ports. All

13 Mode 1—Untagged Frames Only In this mode, the unit functions as a managed MAC layer switch with management only accepted on the fiber Uplink and

14 Mode 3— Mixed Tagged and Untagged, Block MGMT Domain

15 Mode 4— Port Based Forwarding Port Based Forwarding selection is done on the following screen: Mode 5—Port Based VLANs Only untagged frames ar

16 Each port can assign two different VLANs based on the ingress frame classification. For untagged frames, the DiffServ priority value of the IP

FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A computing device, pursuant

17 Mode 6—Port Based Extra Tag In this mode both untagged and tagged frames can enter the drop ports. Two VLANs per port can be assigned based on

18 In this mode both tagged and untagged frames can enter the drop port. Tagged frames can now be classified based on the PRI value within the inco

19 Mode 7— Port Based Extra Tag, Infrastructure

20 Mode 7 allows the user to define whether a port is a Trunk (passes everything, including management), or a Drop (can add/remove VLAN tags). Unit m

21 Mode 7 also allows the user to define whether PRI or DiffServ values are used to classify incoming frames and whether non-IP frames are classifi

22 Mode 8—VLAN Assigned Mode 8 allows up to 64 VLAN IDs to be defined. Each port can be a tags or No-tags member of a defined VLAN. A tags member

23 Only one No-tags can be assigned to a port; this indicates that all frames entering the port that do not match the assigned members VLAN-ID list ar

24 Bandwidth Limiting Bandwidth Limiting can be set per port in both transmit and receive directions. The limiting function provides a Leaky Bucket

25 Port Configuration The Giga-AccessEtherLinX-II Downlink Ports can be configured via console configuration. Type ports and press Enter to be taken

26 System Descriptions This screen allows the user to define unit and port names that are incorporated by the unit into all SNMP traps. These are ext

ii Table of Contents FCC Radio Frequency Interference Statement ...i Warranty...

27 Using Management iView² is a network management application for IMC Networks intelligent networking devices. It features a GUI and gives network m

28 IP address assigned to the chassis management card. Users may still assign IP addresses to each iMcV-Giga-FiberLinX-II and Giga-AccessEtherLinX-II

29 Using Telnet Assign the Giga-AccessEtherLinX-II an IP Address or use the default IP Address 10.10.10.10, subnet mask 255.0.0.0 before using a Teln

30 Uplink Ports FLT Glows yellow when a fault is detected with the fiber Uplink. Faults include loss of link and half-duplex operation. Half-duplex

31 Strongly recommended: • 128 MB RAM • Pentium III 650Mhz or Faster • 17” Monitor @ 1024 x 768 Resolution or higher Installing and Using iView² iView

32 This equipment is designed to permit the connection of the grounded conductor of the DC supply circuit to the grounded conductor at the equipment.

33 DC Power Supply Precautions The following precautions must be observed when installing the chassis model with an internal DC power supply. 1. Check

34 Specifications Standards IEEE 802.3x Ethernet IEEE 802.3u Auto Negotiation IEEE 802.1q VLAN IEEE 802.1p Packet Prioritization Operating Temperatur

35 Fiber Optic Cleaning Guidelines Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, whi

36 Safety Certifications UL/CUL: Listed to Safety of Information Technology Equipment, including Electrical Business Equipment. CE: The produc

1 About the Giga-AccessEtherLinX-II The Giga-AccessEtherLinX-II Series enables service providers to offer differentiated data networking or VPN servic

19772 Pauling y Foothill Ranch, CA 92610-2611 USA TEL: (949) 465-3000 y FAX: (949) 465-3020 www.imcnetworks.com © 2011 IMC Networks. All rig

2 Rackmount Installation The Rackmount kits for the Giga-AccessEtherLinX-II are sold separately: Description Part Number Accessories Installation 19

3 IP-Less Management in HOST/REMOTE configurations A proprietary, secure management communication channel is supported whenever the Giga-AccessEtherLi

4 About iView² Unit Management iView² is a network management application for IMC Networks’ intelligent networking devices. It features a GUI, which

5 SNMP, Telnet and Console Management SNMP, Telnet, and iConfig management channels are always supported through the Giga-AccessEtherLinX-II Uplink P

6 Main Configuration Screen After running through an initial self test, the screen will display: Press Enter for Device Configuration. Press Enter to