Imc-networks IE-IMCV-T1-MUX/4 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Imc-networks IE-IMCV-T1-MUX/4. IMC Networks IE-IMCV-T1-MUX/4 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 36
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
IE-iMcV-T1-Mux/4 + Ethernet
Operation Manual
Zobrazit stránku 0
1 2 3 4 5 6 ... 35 36

Shrnutí obsahu

Strany 1 - Operation Manual

IE-iMcV-T1-Mux/4 + Ethernet Operation Manual

Strany 2 - Warranty

6 iView² Management Software iView² is the IMC Networks management software designed specifically for the IMC Networks “iMcV” family of modules. It f

Strany 3

7 LED Operation The IE-iMcV-T1-Mux/4 + Ethernet features diagnostic LEDs as explained below. 10/100BaseT Connector LNK: • OFF when port is not li

Strany 4

8 SFP Ports or One model offers two SFP (A and B) ports for 1+1 protection; a second model offers one SFP without protection. ACT: • Glows gre

Strany 5

9 DIP Switch Assignments DIP Switch Assignments A single 10-position DIP Switch is located on the unit to set the configuration. The switch positions

Strany 6

10 Installation Instructions Each IE-iMcV-T1-Mux/4 + Ethernet module requires two slots in an iMedia Chassis Series, MediaChassis/2 Series, or IE-Medi

Strany 7 - Console RS232

11 Configuration Options The following sections describe the configurable features. From the CLI "Unit Configuration," use the "Facto

Strany 8

12 Fiber Fault Loopback (FFL) When a Fiber LOS is detected, the unit sends a Remote Alarm Indication) back to the fiber in the opposite direction. Th

Strany 9

13 Loopback Each T1 port can be tested in loopback mode by enabling either a Host loopback or Remote loopback test path. This capability allows the e

Strany 10

14 Console Screens Configuration Using the Console Port The following section describes configuration using the console screens. The Remote module is

Strany 11

15 Main Menu From the main menu, the end-user can view essential unit configuration data and a clock indicating when the displayed information was las

Strany 12

FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A computing device, pursuan

Strany 13

16 The screen displays the current status for items 1 through 8. For security reasons, the current username and password are not displayed. For item

Strany 14

17 SFP Line Status Screen The SFP Line Status screen displays the status of the Host and Remote SFP links. The detailed SFP information may be view

Strany 15

18 Enter the number of the menu item to change its configuration, and then enter the new value(s) when prompted. Ethernet Port Status Screen This scre

Strany 16

19 Host T1 Port Setup Screen Enter the number of the menu item to edit, and enter the new value(s) when prompted. T1 Port Status Screen Use this sc

Strany 17 - T1 Mux HOST T1 Mux REMOTE

20 Fiber Optic Port Verification As a troubleshooting aid, the fiber optic ports can be verified by placing a physical loopback optical line on the po

Strany 18

21 T1 Port Verification By placing a physical loopback connection on the T1 port, a valid signal can be detected by each individual T1 port to verify

Strany 19

22 T1 Port Mating Connector Pinout The following table lists the pin configuration for the standard RJ-48 T1 port mating connectors. Pin Signal 1

Strany 20

23 RS-232 Serial Console Port The following table lists the pin configuration for the RS-232 3-pin Mini Jack mating connector for the console serial p

Strany 21

24 Troubleshooting • All IE-iMcV-T1-Mux/4 + Ethernet units are shipped configured as Host units via DIP Switch #1 = OFF. The Remote unit should be set

Strany 22

25 Specifications Power Consumption (Typical): 0.96A @ +5 VDC Operating Temperature: +32°F to +158°F (0°C to +70°C) Storage Temperature: -40°F to +158

Strany 23

ii Table of Contents FCC Radio Frequency Interference Statement -------------------------------------------------- i Warranty ------------------------

Strany 24 - WARNING

26 Definition of Terms/Acronyms The following are terms and phrases used within this manual, or which are found in documents associated with this equi

Strany 25 - Pin Signal

27 FFL Fiber Fault Loopback: When the fiber line fails, the Ethernet port that is being forwarded over the fiber line is forced out of LINK. Simila

Strany 26

28 RAI Remote Alarm Indication: Status information received from the line indicating there is an alarm condition at the far end of the transport. SF

Strany 27 - Tip

29 IMC Networks Technical Support Tel: (949) 465-3000 or (800) 624-1070 (in the U.S. and Canada); +32-16-550880 (Europe) Fax: (949) 465-3020 E-M

Strany 28

30 Fiber Optic Cleaning Guidelines Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, whi

Strany 29

31 Certifications CE: The products described herein comply with the Council Directive on Electromagnetic Compatibility (2004/108/EC). European

Strany 30

19772 Pauling • Foothill Ranch, CA 92610-2611 USA TEL: (949) 465-3000 • FAX: (949) 465-3020 www.imcnetworks.com © 2010 IMC Networks. All ri

Strany 31

iii Troubleshooting -------------------------------------------------------------------------------------24 Specifications----------------------------

Strany 32

1 About the IE-iMcV-T1-Mux/4 + Ethernet Overview The IE-iMcV-T1-Mux/4 + Ethernet is a media converter that transports four independent T1 lines over a

Strany 33

2 The IE-iMcV-T1-Mux/4 + Ethernet offers the following features: • Four T1 ports with RJ-48 connectors • One full bandwidth Ethernet 10/100BaseT port

Strany 34

3 Product Application The IE-iMcV-T1-Mux/4 + Ethernet delivers 4 T1 lines to a customer's site over a protected, dedicated fiber line. In additi

Strany 35

4 configuration on the unit will be used. The stored configuration can be retrieved from the SNMP Management Module or the DIP Switches. • Replacing t

Strany 36

5 1+1 Protection on the Fiber Interface mode The fiber transport is a 1+1 protection switched transport. It provides very fast (<50 mSec) switch-to

Komentáře k této Příručce

Žádné komentáře